Skip to content 
In the streaming industry today, Roku is really making huge advancement as one of the most acceptable devices for comprehensive entertainment via multimedia streaming. In fact, the smart device is always a click away to make our lives better. Despite its super cool operating system together with the advanced technology used to design the device, Roku still experiences several errors which can occur without prior warning.
This interruption can really pose as a hindrance from getting the best of your Roku device. The โNo Signal Issueโ is among the recurrent errors youโre likely to notice as you make use of your Roku device. Smacking the previous model often tend to correct the device, but with this present model, a different problem might occur if you want to replicate that trick. In this write-up, weโll share the causes of the No Signal issue and possible solutions on how to rectify it.
Table of Contents
How to fix the Roku No Signal Issue in 7 steps
If youโve been noticing this error, below are some things you can actually do by yourself to fix it.
Check for any possible outage
If youโre not careful, you can really mess up things when you refuse to check for any possible outage. This means that before you begin any troubleshooting, this must be checked. This is because the outage from your ISP can result in no signal error. At this point, you can reach out to your ISP to confirm if they had any power outage. If the answer is No, then expect it to start functioning again.
Wipeout dust from the ports
Over time as you make use of your device, dust can be settling around the port without you knowing about it. So form it as a habit to clean the HDMI and coaxial ports of your Roku device to remove any dust that must have eroded around it. Plug it back when youโre done cleaning. This alone can go a long way to solve the issue for you; then you can start enjoying your device again.
This also goes hand in hand with any fan noise problems, its recommended to periodically clean the vents to prevent overheating issues.
Check all cables together with the connector
Most people tend to neglect this without knowing it is very crucial. All the cable and connectors must be observed appropriately to see if there are any torn, corrosion or ruptured ends. These can seriously affect connectivity. When this has been thoroughly done, plug back everything as it was at first. Most times, this can put an end to the No signal issue.
Restart the Roku device
Restarting the device is also another method of checking the no signal issue, especially when it suddenly happened without any warning. At this point, all you need to do is to unplug your device from the power source, allow it for a few minutes, then reconnect it. The few minutes used to carry out this task is enough to fix any error on your Roku device.
Reset the Settings of the Roku device
Maybe youโve tried restarting the device without any positive change, then resetting the device might be another step you need to take. First, navigate to the advanced system setting, click on reset, then factory settings. Allow it for some minutes until the resetting has been completed and the device back to its original state. Now you can proceed to make use of your device without any challenges.
Update Roku
So far if none of the above-listed solutions didnโt show any positive change, then you need to update your Roku, especially when youโve not done this before. To do this, navigate to settings, scroll to the about information and click the software version. Once Roku has released a new update, youโll be able to see the notification here. Just proceed and update the firmware. At the end of the update, the Roku device will restart by itself. Now you can continue making use of your device.
Contact Support
Reaching out to the customer service department is the last resort to take when every other method has failed. From their end, theyโll do a thorough analysis of your device and make a possible recommendation to put an end to the No signal issue once and for all.
In Conclusion
Like we stated earlier in this write-up, Roku device has proven to be a fantastic piece of entertainment hardware that can serve as an ideal replacement for your regular cable TV. Just like every other device of this sort, there are still loopholes that may hinder you from enjoying the service without hitches. Whenever you tend to experience any No signal issue, carefully follow the recommendations outlined in this write-up in other to fix it.
FREQUENTLY ASKED QUESTIONS
My Roku suddenly stopped working, what could be the cause?
Whenever you notice this, first you must unplug the power cord from the device and allow it for a few minutes before reconnecting it again. As it comes on, remove the batteries and reinsert it again inside the remote control. There is a black pairing button around the battery compartment, press and hold it for five seconds as you still allow the Roku device to boot.
Am finding it difficult to connect my Roku device to my TV.ย
You need to ensure that the Roku device is correctly connected to your wireless network. Better still you can restart the app by long-pressing the reset button and then swipe the app to shut it off.
My Roku canโt come on. Why?
In most cases, this is caused when the power cord is not correctly plugged. So you need to ensure it is properly placed. However, when it still wonโt come on, you need to reach out to the customer support department for further instruction o what to do.
My Roku TV suddenly started saying no signal. Why?
First, check all the input and ensure all are their correct port. Better still you can make an effort to change the input or the source to the TV, AV, DTV or Digital TV, mostly when youโve not done so. If the fault is not from there, then the next suspect might be the antenna or setup fault.
