Skip to content 
Error codes such as the DirecTV code 772 always refer to a specific malfunction on your device. In some cases, some of these errors result from a power supply or cables that were mistakenly disconnected. These can also be seen after the occurrence of a storm that ends up turning off your receiver or even tampering with elements linked to your DirecTV setup.
Table of Contents
What is the error 772
If you see DirecTV code, 722 error message appear on your DirecTV receiver, what it means is that there has been an interruption within the programming information. You donโt need to worry yourself about this because you can fix it by simply following the steps outlined below.
Reset the receiver
Resetting the receiver is the first thing you need to do. This can be done by simply pressing the red button that can be seen on the receiver. In some models, this can be seen at the side or the back of the receiver. On average, youโve to be patient for 10 minutes for it to be completed. Also, know that you might not be able to receive live TV until like an hour. But be fully assured that the error message will eventually be fixed.
Signal Issues
If the reset didnโt resolve the error message, then most likely, the error might result from loss of signal. This means that your receiver is not getting adequate signal like it is supposed to be, which has caused the programming issue. Therefore, you need to relocate the receiver to another place for optimal signal reception.
Furthermore, a frequency blockade around the receiver can also result in loss of signal. This happens when you have a microwave, router, or TV very close to the receiver. Hence, changing the location of the receiver where their wonโt be frequency interference is advisable.
Strength of the Satellite Signals
In a situation where the receiver is placed in an optimal position and still wonโt work, then the strength of the satellite will need to be checked. Bear this mind; the satellite strength must be higher than 85%. Hence, check the satellite signal to see if itโs up to that percentage
Network Tuner for data guide
A good number of dish receiver has its network tuner, which helps to receive data guide. So the network tuner should be checked. To do this, press the guide button followed by the right arrow, which can be seen on the front panel. This will lead you to the test menu, choose the coax network from there. Doing this will help tune up the network for better performance.
Reach out to Customer Support
If none of the solutions helps correct the 772 messages, then it might be that there is a problem at the backend. At this point, itโs advisable to reach out to customer support and narrate your experience. Your network will be observed from their end. A technician will be sent to your house to inspect your receiver correctly. Alternatively, you might receive a free house call once you have a DirecTV protection plan, but the troubleshooting procedure needs to be followed accordingly.
In Conclusion
The suggested solutions listed in this write-up will help you put an end to the DirecTV code 772. This means that you do not necessarily have to sit and wait until DirecTV sends a technician to your house to rectify it. This suggestion was completely updated. However, for further support, youโre free to reach out to DirecTV customer support.
Frequently asked questions
What is the meaning of DirecTV code 722?
This error code indicates that the DirecTV receiver youโre using lack the appropriate programming information for the channels to function effectively.
My Directv keeps glitching. What could be the cause?
On a general note, the freezing error when there is a TV signal disruption or lack of signal. You need to wait for the signal to be correctly initialized. Alternatively, you can reset by unplugging the TV, press and hold the power button and wait for at least 30 seconds before you finally release it.
How do I rectify errors on my DirecTV connection?
The receiverโs network connection needs to reset. After this, if there is a possible improvement of connection, observe the cable connections, and reset the router. The SWM should also be unplugged and plugged back in. These have a role in correcting it.
What are the steps to restart a receiver?
By merely restarting your receivers, the problem can be solved. For a minimum of ten seconds, press and hold the power button. This usually takes an average of 5-9 minutes to be completed. But know that it will significantly impact any DVR recordings that might be in process. Those with multiple receivers should unplug the wireless gateway from the source and then allow it to reboot.
Whatโs the outcome if I reset my Directv receiver?
You can see the reset button at the swingout door on your DVR and receiver. This will restore your device to the default settings, but it will keep your recordings. However, your RF remotes need to be paired again. Also, youโll need to set any preference you once had before the reset.
What could be the cause of why my receiver is shutting off?
The premature shooting of the receiver is always a result of problems linked to the receiver and the speaker wiring. For instance, if there is a single strand of wire in the wrong place, it can bring about short circuit errors, which will, in turn, cause the unit to shut off and cause low volume levels.
Explain DirecTV error code 721?
This can usually mean two things; either that particular channel is different from your programming package. Besides, it might mean you need to refresh your service.
